• Automatic network-provided time zone is not update

    Dear NXP,   I got trouble when set "Use network-provided time zone" . It is not updating the time zone (needs update to GMT to IST). Still it is in GMT only. I checked WiFi working properly.    I...
    vinothkumar s
    last modified by vinothkumar s
  • Enable GmSSL which supports OSCCA Algorithm Toolbox on i.MX

    GmSSL is an open source cryptographic toolbox that supports SM2 / SM3 / SM4 / SM9 and other national secret (national commercial password) algorithm, SM2 digital certificate and SM2 certificate based on SSL / TLS secu...
    Xiaodong Zhang
    last modified by Xiaodong Zhang
  • How can I set the frequency of im8mq GPU to 1 GHz

    In im8m evb board & Linux image.Seem the GPU frequency is fixed at 800 MHz. But I check the GPU frequency can be boom up to 1000 MHz. If don't consider overheat problem, how can I set to 1000 MHz?   Thanks.
    Liou Harry
    last modified by Liou Harry
  • 移植开源的密码工具箱GmSSL到i.MX平台

    Xiaodong Zhang
    last modified by Xiaodong Zhang
  • v4l2src device=/dev/video0 not working

    When  gst_rtsp_media_factory_set_launch (factory, "( "      "v4l2src device=/dev/video0 ! video/x-raw !  "       " rtph264pay name=pay0 pt=96 " ")");   gett...
    Santhosh Kumar
    last modified by Santhosh Kumar
  • How can I change the target of my U-boot from SD Card to NAND?

    Hello, everybody.   I want to change u-boot's Config from SD Card to NAND.   However, an error will occur even if you proceed as shown in the manual and the following link.   * manual name = i.M...
    Seung Hyun Park
    last modified by Seung Hyun Park
  • How can I get the gpu loading at im8mq

    As title, /unit_tests/GPU/ has gpuinfo.sh script file to show the info. of GPU I think the idle my be the un-loading of GPU, but the value is always 0 and seem the script is wrong.(the /sys/kernel/gc/idle no $7) ...
    Liou Harry
    last modified by Liou Harry
  • imx6 yocto consultant

    I need to get some support from an expert.  We have developed our own board based on the imx6 and I need to modify the yocto build to support our board.  I can pay for hourly support. Y-
    Yile Ku
    last modified by Yile Ku
  • Physical memory address of DMFC

    From i.MX 6Solo/6DualLite Applications Processor Reference Manual, Rev. 4, 07/2018 FIFO allocation to channels The physical memory is partitioned to 8 segments. For each channel the user has to defi...
    Kazuma Sasaki
    last modified by Kazuma Sasaki
  • i.MX6 duallite-60FPS

    Dear all,   we are using IMX6 Dual processor to run a Full HD Animated image in our TFT. Now the image Frame rate 30 FPS. Does our processor have the capability to run the same in 60 FPS?   NOTE: 1. In ...
    Muthuraj M
    last modified by Muthuraj M
  • about IMX6D uboot

    Refer to the official imx6q board to customize the imx6d board(pmic and ddr3 are the same ),but can't use mfgtools to download uboot. especially, loading U-boot all the time. who can help me ? where should i modify ?
    cot way
    last modified by cot way
  • The Manufacturing Tool failing to flash

    I'm trying to use the Manufacturing Tool MfgTool2.exe to flash my MCIMX6Q-SDB SABRE board, I've tried both SDCard and eMMC and I'm getting the same results, the tool hangs during the partition step.   From the D...
    Michael Worster
    last modified by Michael Worster
  • How to open .img file

    On nxp website, I have downloaded the android image android_o8.1.0_1.4.0_7ulp-ga_tools.tar.gz and from there, I run script mfgtool2-android-mx7ulp-evk-sd.vbs To load the android image to the SD card. I disagree wit...
    david cammeron
    last modified by david cammeron
  • DisplayPort Multi Stream Transport (MST) Support on i.MX8M

    i.MX8M support DisplayPort 1.3, but is Multi-Stream Transport supported by display drivers on Linux?
    Yevgen Kyriukha
    last modified by Yevgen Kyriukha
  • Low cost i.MX6 dev board with MIPI-CSI2?

    What is the lowest cost i.mx6 development board that supports a camera interface with four lanes of MIPI-CSI2?   Also, I need it to have Yocto support.   Thank you,   Bob
    Robert Cochran
    last modified by Robert Cochran
  • Restriction of i.MX8QXP 24MHz XTAL Cload value

    Hi,   Are there some restriction of i.MX8QXP Xtal CLoad. According to the data sheet 4.4.1 OSC24MHz, i. MX8QXP internal XTAL circuit has integrate trimmable internal loading capacitors. So we understand that we...
    Mamoru Kanou
    last modified by Mamoru Kanou
  • Linux config options to support i.MX6Solo and i.MX6DualLite SoC

    I would like to strip down as much as possible my configuration file for a single Linux kernel image that will be used on boards with the two mentioned SoCs.   The main question is: Which SoC options are the ba...
    Michal Vokac
    last modified by Michal Vokac
  • Run FreeRTOS on i.mx8m with small size of DRAM

    Hello, NXP technical support team:   We made a i.mx8M board with 3 kinds of DDR size: 1GB, 2GB and 3GB. For the i.mx8M board with 1GB DDR, it can't run "rpmsg_lite_pingpong_rtos_linux_remote.bin"  in DDR (...
    Richard Hu
    last modified by Richard Hu
  • Using UART2 from Linux on i.MX8M-EVK board

    On the i.MX8M-EVK board there are two UARTs available through the USB micro socket, which is fine. One is used as a Linux console and the other is connected to the Cortex-M4 core.   In my case I would not use t...
    Bernard Dautrevaux
    last modified by Bernard Dautrevaux
  • UUU command to dowload image to IMX6 ULZ

    Hi, I am using imx uuu to download Linux image to NAND of a custom IMX6 ULZ, the image rootfs-sd.wic.gz was built by Yocto, it can be installed to an SD card and boot from IMX6ULZ evaluation board. Can the same image...
    jupiter hce
    last modified by jupiter hce