• IMX6QP + Sony IMX290 CMOS via MIPI

    We have an own IMX6QP board communicating with an own CMOS sensor board (Sony IMX290 based) via MIPI interface. We developed a camera driver and also modified some of the NXP BSP files and more or less the solution is...
    joan vicient
    last modified by joan vicient
  •    Boot process issue | i.MX6Q Sabreauto

    Hi, Iam building android 7.1.2 SabreAuto BSP for our board ,successfully  flashed images into 16Gb microSD card using script fsl-sd-card-partition.shwhich is attached below.But when we powered on our board ...
    RICHU C J
    last modified by RICHU C J
  • i.MX Power Profiling System: Instrumenting A Board

    Instrumenting A Board To instrument a board, the connection between the power supply and the target device needs to be broken, usually via a series resistor that's placed on the board. Sometimes the inductor needs to ...
    David G Dicarlo
    last modified by David G Dicarlo
  • The Manufacturing Tool failing to flash

    I'm trying to use the Manufacturing Tool MfgTool2.exe to flash my MCIMX6Q-SDB SABRE board, I've tried both SDCard and eMMC and I'm getting the same results, the tool hangs during the partition step.   From the D...
    Michael Worster
    last modified by Michael Worster
  • i.MX Power Profiling System: Smart Current Sensor and Aggregator Shield

    NOTE: Always de-power the target board and the aggregator when plugging or unplugging smart sensors from the aggregator.   NOTE: See this link to instrument a board with a Smart Sensor.   Over...
    David G Dicarlo
    last modified by David G Dicarlo
  • i.MX Power Profiling: Triple-range Smart Current Sensor

    NOTE: Always de-power the target board and the aggregator when plugging or unplugging smart sensors from the aggregator.   NOTE: See this link to instrument a board with a Smart Sensor.   This...
    David G Dicarlo
    last modified by David G Dicarlo
  • Output format of imx vpu decoder

    Hi,   I am using decode-example from libimxvpuapi package to decode h264 file. I am not sure about the output format of the decoder. Is it YUV420 or YUV422? If it is not YUV422, can we decode h264 file to prod...
    girijapretha
    last modified by girijapretha
  • how to config DDR clock of i.mx6q

    Hi everyone, I'm developing a new board based on the IMX6Q. We have make the DDR's clock root from 528M successfully.The uboot's version  what we use is 2009.08. We want to make DDR running at 400M f...
    li hu
    last modified by li hu
  • Extra bit when using native slave select on imx6

    I am using native cs pins for SPI master configuration as below: &ecspi2 {         pinctrl-names = "default";         pinctrl-0 = <&pin...
    Abhinandan B R
    last modified by Abhinandan B R
  • how to connect HDMI display to MCIMX6QP-SDB

    I bought  MCIMX6QP-SDB recently. I am trying to connect HDMI monitor to J8 on MCIMX6QP-SDB.   I used the following BSP(u-boot-2018-03, linux-imx-4.9.88).   repo init -u https://source.codeaurora.or...
    M C
    last modified by M C
  • i.mx6q sabresd flexcan not working

    I am running Android 8.0 with canutils 4.0.6 and have configured dtsi and enabled flexcan in configs. Installed a DB9 connector on J10 on both boards.   130|sabresd_6dq:/ # dmesg | grep can [ 0.512749] i2c i2c-...
    Aravind Srinivasan
    last modified by Aravind Srinivasan
  • Yocto Build Error

    Hi, I'm trying to get familiar with yocto project for imx6qsabreauto.I'm referring imx_yocto_userguide.I get following error every time executing the command 'bitbake core-image-base'.   ERROR: Unable to start ...
    RICHU C J
    last modified by RICHU C J
  • USB3.0 Not working with imx6qp

    Hi, I am having custom board with imx6qp and TI TUSB7320 USB3.0 controller connected on PCIe. The USB controller is getting listed with lspci command. Also after enabling xHCI driver, two usb 3.0 root hubs are also s...
    Pratham Rahte
    last modified by Pratham Rahte
  • RGMii Signal Spacing 1000b 125Mhz

    It is accepted that cross talk is generally reduced when S >3W or S>5W for aggressive lines as a rule of thumb. Are general constraints in regard to  RX/TX Data[3..0] trace spacing applicable to RGMii when...
    DAVID SABALESKY
    last modified by DAVID SABALESKY
  • Useful documents and threads of i.MX Processors

    The following document contains a list of document, questions and discussions that are relevant in the community based on amount of views. If you are having a problem, doubt or getting started in i.MX processors, you ...
    Erik Bustos
    last modified by Erik Bustos
  • IMX6Q Sabre Yocto build fail

    Hi everyone,   I try to build Yocto for IMX6Q Sabre based on distro fsl-imx-xwayland with one more additional layer from Laird Connectivity because I have one more module wifi from LAIRD:   GitHub - LairdC...
    Minh Nguyen
    last modified by Minh Nguyen
  • How to handle the interrupt_uart interrupt on imx6 ?

    Hello,   I am using UART 3 on imx6 and I want to know when my first byte is being sent. At the moment, I'm polling the TXDC flag to know it but I want to do it with an interrupt.  The TCEN bit in UCR4, al...
    Florian Gaudon
    last modified by Florian Gaudon
  • how to connect usb camera to MCIMX6QP-SDB

    I bought  MCIMX6QP-SDB recently. I am trying to connect USB CMOS Camera(logitech C920) to USB OTG port on MCIMX6QP-SDB.   I used the following BSP(u-boot-2018-03, linux-imx-4.9.88).   repo ini...
    M C
    last modified by M C
  • How to run CVE checker on yocto image for iM6SX

    Hi Guys We are using customized yocto linux kernel and running some C++ code for industrial application.   Where i can find CVE (Common Vulnurabilites and Exposures) tools to check for my custom-ed yocto i...
    Pranav Mondhe
    last modified by Pranav Mondhe
  • how to build custom android 8 kernel

    i can customize and build android kernel separately from android system as discribed in Android_User's_Guide.pdf, but when build android system, kernel config replaced to some kind of default config (imx_v7_android_de...
    Andrey Kononov
    last modified by Andrey Kononov