• How many sc16is752 could be used at most on iic bus at the same time?

    Hi everyone, In the datasheet of SC16IS752_SC16IS762(Rev. 9 — 22 March 2012),  "10.3 Addressing  Table 32. SC16IS752/SC16IS762 address map", it says there are 16 address could be selected by usin...
    lau jo
    last modified by lau jo
  •    Boot process issue | i.MX6Q Sabreauto

    Hi, Iam building android 7.1.2 SabreAuto BSP for our board ,successfully  flashed images into 16Gb microSD card using script fsl-sd-card-partition.shwhich is attached below.But when we powered on our board ...
    RICHU C J
    last modified by RICHU C J
  • Recorded Video files time and date is not update and it's showing unix time

    Dear NXP,   I am working on IMX6Q with Android 7 for video recording. After done Video record the file is saved in SATA partition. If I check the details of recorded file shows some wrong unix date and time (01-...
    vinothkumar s
    last modified by vinothkumar s
  • Wayland Weston Desktop i.MX8M

    Hi,   I am currently working on installing Wayland Weston Desktop Environment on Ubuntu 16.04 for the i.MX8M but have an issue. Once i install and try to run I only get a black screen. It seems like the weston i...
    Cesar Hernandez
    last modified by Cesar Hernandez
  • i.MX Power Profiling System: Instrumenting A Board

    Instrumenting A Board To instrument a board, the connection between the power supply and the target device needs to be broken, usually via a series resistor that's placed on the board. Sometimes the inductor needs to ...
    David G Dicarlo
    last modified by David G Dicarlo
  • bitbake -c populate_sdk_ext failed in imx-4.9.88-2.0.0_ga

    I'm building the latest source on codeaurora.org for imx6q: repo init -u https://source.codeaurora.org/external/imx/imx-manifest -b imx-linux-rocko -m imx-4.9.88-2.0.0_ga.xml DISTRO=fsl-imx-f...
    计龙 杨
    last modified by 计龙 杨
  • How to build ubuntu 14.04 or 16.04 LXDE for i.MX6 Quad sabresd

    Hi Community, I'm trying to build ubuntu rootfs version 14.04 or 16.04 with LXDE desktop for i.MX6 Quad sabre-SD.   I refer to below website   I did paragraph 2: Installing the Ubuntu core, Lubuntu g...
    tsung li wang
    last modified by tsung li wang
  • How can I change the target of my U-boot from SD Card to NAND?

    Hello, everybody.   I want to change u-boot's Config from SD Card to NAND.   However, an error will occur even if you proceed as shown in the manual and the following link.   * manual name = i.M...
    Seung Hyun Park
    last modified by Seung Hyun Park
  • enable color_key in runtime

    Hello, I have an application that is responsible for viewing video with gstreamer. The main application is shown in /dev/fb0 and the video in fb1. I have configured fb0 to be the foreground and I also configure the co...
    Alex V
    last modified by Alex V
  • How is the USB disconnection detection working in i.MX6?

    Hello Hi,   We are developing a product based on i.MX6 Dual lite running linux on it.  It has a USB port supporting both HOST and DEVICE modes (using  i.MX6 OTG USB port). We are ...
    Sonu Kurian
    last modified by Sonu Kurian
  • Automatic network-provided time zone is not update

    Dear NXP,   I got trouble when set "Use network-provided time zone" . It is not updating the time zone (needs update to GMT to IST). Still it is in GMT only. I checked WiFi working properly.    I...
    vinothkumar s
    last modified by vinothkumar s
  • i.MX6 duallite-60FPS

    Dear all,   we are using IMX6 Dual processor to run a Full HD Animated image in our TFT. Now the image Frame rate 30 FPS. Does our processor have the capability to run the same in 60 FPS?   NOTE: 1. In ...
    Muthuraj M
    last modified by Muthuraj M
  • Linux config options to support i.MX6Solo and i.MX6DualLite SoC

    I would like to strip down as much as possible my configuration file for a single Linux kernel image that will be used on boards with the two mentioned SoCs.   The main question is: Which SoC options are the ba...
    Michal Vokac
    last modified by Michal Vokac
  • i.MX Power Profiling System: Smart Current Sensor and Aggregator Shield

    NOTE: Always de-power the target board and the aggregator when plugging or unplugging smart sensors from the aggregator.   NOTE: See this link to instrument a board with a Smart Sensor.   Over...
    David G Dicarlo
    last modified by David G Dicarlo
  • i.MX Power Profiling: Triple-range Smart Current Sensor

    NOTE: Always de-power the target board and the aggregator when plugging or unplugging smart sensors from the aggregator.   NOTE: See this link to instrument a board with a Smart Sensor.   This...
    David G Dicarlo
    last modified by David G Dicarlo
  • Need Information/datasheet for ov5645 camera module

    Dear NXP,   I am working on imx6q with Android 7. I want to integrate ov5645 camera. But, i am not getting exact datasheet. I know some of view working on this camera.   If it possible please provide ...
    vinothkumar s
    last modified by vinothkumar s
  • iMX8M Mini Serial Port (UART 3)

    Hi Sir, I have iMX8M mini EVK and I am able to connect my iMX8M mini to my laptop via USB Micro B debug port of iMX8 Mini. and i am bale to see the console output in putty / minicom.   from the documents i came...
    Maneesh Singh
    last modified by Maneesh Singh
  • iMX6-Dual Display with vivante and X11(xserver) only one is possible with acceleration, How to use another without acceleration ?

    Hi Community,   I am using imx6 with our custom board, and trying to use dual display (LVDS+HDMI). kernel version -4.1.15 X11(xserver) version-1.18.0 Vivante (Galcore) - 5.0.11   I know accelerated dual...
    Pankaj Suryawanshi
    last modified by Pankaj Suryawanshi
  • DS90UB914A-Q1/913 camera capture image problem

    i am using DS90UB914A-Q1/913 camera to capture image i can receive 913 camera data and save those,but the image is green. like below: the 913 camera format is ccir601 8bit (UYVY),1280*720. the CSI0 Sensor Configu...
    lin ben
    last modified by lin ben
  • Suggestion for camera

    Dear NXP,   I am working IMX6Q with Android Nought. I want to interface the camera with my Custom board. I have 15 pin camera connector. I want the compatible camera for this camera connector.   Now I am u...
    vinothkumar s
    last modified by vinothkumar s